Central AC for apartments
Apartment central AC in Taiba
In Taiba, north-east Jeddah, fitting central AC in apartments faces unique challenges because buildings are newer and flats are larger. Alrabih's team carefully designs the ductwork to cool multi-room units while keeping energy use and noise low.
- Tight ceiling
- Sealed drain
- Quiet running
Clients We're Proud to Serve
Organisations and companies that trusted Alrabih with their projects.
When central AC makes sense in your flat
- 1
New flat before finishing
The finishing stage is the right time to install central AC. The ceiling is open and walls are ready for copper and drain routes, so there is no need later to cut plaster or damage finished surfaces.
- 2
Occupied flat where splits fall short
If splits leave hot and cold patches, or the noise bothers you at night, central AC distributes air evenly and hides the unit away from the room. A site survey decides whether your ceiling height allows it.
- 3
Your unit disturbs the neighbours
In apartments, neighbours hear unit vibration through shared ceilings and walls. We choose the indoor unit suspension point carefully and use flexible collars on the air outlets to absorb vibration before it reaches the building structure.
Who it's for
Living in a furnished flat and want to replace splits
We survey your ceiling void to see whether a concealed unit fits, then run copper and drain without disturbing the existing décor.
Ask on WhatsAppBuying a flat in a building under construction
We coordinate with the finishing stage to run copper, drain and ducts before ceilings and walls are closed, so every route stays fully concealed.
Ask on WhatsApp
What the installation covers
- Ceiling survey and unit position
- Mueller copper fully insulated
- Condensate drain with correct fall
- Air ducts and distributed outlets
- Line vacuum and start-up test
How we work
How we work
- 1
Ceiling and route survey
We measure the available ceiling void, decide where the indoor unit hangs, map the copper route and find where condensate drains without causing damp. The survey decides whether one zone or more suits the flat.
- 2
Run copper and drain
We run insulated Mueller copper in the void above the suspended ceiling and slope the condensate line towards the building drain or an external outlet, so no standing water causes odour or damp.
- 3
Fit ducts and outlets
We mount the indoor unit on vibration-absorbing hangers, route ducts to each room and place every outlet so air spreads evenly without blowing cold air directly onto anyone.
- 4
Vacuum, test and hand over
We vacuum the copper line to remove air and moisture, check all joints, then run the unit and confirm cooling in every room before we hand over.
A considered install or a hasty one?
| Alrabih | The usual way | |
|---|---|---|
| Indoor unit position | Set after measuring the void | Wherever it fits |
| Condensate drain | Calculated fall to building drain | May pool and cause damp |
| Vibration | Absorbing hangers, flexible collars | Reaches the neighbours |
| Air distribution | Outlets placed for even spread | Cold rooms and warm rooms |
| Salty sea air | Mueller copper, tight flared joints | Early joint corrosion |
Everything your AC needs, from one team
From system design and duct fabrication to installation, commissioning and maintenance.
Split AC installation
Request this serviceDuct installation
Request this serviceCentral AC installation
Request this serviceDuct fabrication
Request this serviceCold room installation
Request this serviceElectro-mechanical works
Request this serviceChiller & AHU installation
Request this serviceHVAC design
Request this serviceAC repair & faults
Request this serviceAC cleaning
Request this serviceRefrigerant charging
Request this serviceCentral AC maintenance
Request this serviceChiller maintenance
Request this serviceAC removal & refitting
Request this serviceDuct cleaning & sanitising
Request this serviceAC servicing by brand
Request this serviceOperation & maintenance contracts
Request this serviceAHU maintenance
Request this serviceFridge & freezer service
Request this serviceCold rooms
Request this serviceDisplay fridges & chillers
Request this serviceFactory HVAC
Request this serviceWarehouse HVAC
Request this serviceVilla & home HVAC
Request this serviceHotel HVAC
Request this serviceSchool HVAC
Request this serviceHospital HVAC
Request this serviceMosque HVAC
Request this serviceMall & retail HVAC
Request this serviceRestaurant & cafe HVAC
Request this service
Some of our work
Ductwork, rooftop units and diffusers, from work we've completed in Jeddah.
Customer reviews
What our customers say
- Muhammadramzan 2641
“MashaaAllah. Services are so good. Behaviour and kindness 100/100. Prices are less then Market. Fully recommended”
- shahzeb armani
“Wow. Prices are so comfortable. Outstanding services. People are so talented and nice”
- Tawfik AlyawerLocal Guide
“U can find all u need for air conditioning”
Your satisfaction matters to us! If you had a great experience with us, we'd love a 5-star rating and a kind review.
Worked with us? Leave a reviewService areas
We come to you anywhere in Jeddah
From Al Shiraa and Al Yaqout in the north to Al Thaghr and Al Quraiyat in the south, with our base in Al Aziziyah.
What sets this district apart
Taiba comprises relatively newer tall residential buildings with spacious flats and more bedrooms than other northern districts. Ceilings are slightly higher and ceiling voids are more generous, but ductwork design must still balance cooling large areas with minimising heat loss and ensuring even temperature distribution across every room.
Taiba is in north-east Jeddah, a district of modern contemporary residential blocks with spacious flats and open layouts.
Most Taiba flats are three or four-bedroom, and suspended ceilings offer adequate space for main duct runs.
The AC setup in Taiba
- 1
Ducts distributed to multiple bedrooms
Taiba's spacious flats need strong main ducts branching evenly to each bedroom and living area.
- 2
Indoor unit sized for the larger area
The indoor unit is chosen based on your flat's total area to ensure adequate cooling capacity for all rooms.
- 3
Centralised safe external drainage
The condensate line from the indoor unit runs as one main line safely outside via the balcony or a secure opening.
Before the visit
Before our visit in Taiba
- 1
Provide a detailed floor plan with measurements
A sketch showing your flat's dimensions, room locations and furniture placement helps us find the best spots for the indoor unit and ductwork.
- 2
Tell us your cooling needs for each room
Does each room need equal cooling or do you prefer different temperatures in bedrooms versus living areas? This affects damper design.
- 3
Confirm balcony and external wall access
Your balcony or external wall must be safe and accessible for fitting the outdoor unit and running the condensate line.
More districts for Apartment central AC
Other services in Taiba
FAQ
Questions about Apartment central AC
Is there enough ceiling space in a flat for a central unit?
It varies between flats. Slim ceiling cassettes need less void depth than full ducted units. A site survey measures what is available and decides the right type; if the corridor ceiling is too shallow we look at a storage room or bathroom ceiling instead.
Is one unit enough for the whole flat or do I need more?
It depends on the flat's area, room layout and how much sun each side receives. Two- and three-bedroom flats can sometimes work with one unit and well-planned ducts; larger flats or those with separate zones may need two. The survey decides.
Where does the outdoor unit go when the flat has no large balcony?
Options include the shared roof if the building rules allow it, a facade bracket away from neighbours' windows, or the balcony if it can take the load. We review the building's rules before recommending any position.
Jeddah's air is very humid; does that affect the condensate drain?
Yes. In Jeddah the indoor unit produces more condensate because of the high humidity. We make sure the drain line has enough fall, that the horizontal run before it drops is not too long, and that the outlet does not conflict with other flats' drainage in the building.
Can the flat be split into two zones with different temperatures?
It is possible using two separate indoor units or by adding variable-flow dampers on the duct runs. The right choice depends on the flat's layout and the ceiling void available in each zone. A site survey decides which approach suits your room arrangement.
My flat is very large, will central AC cool every room evenly?
Yes, if the ductwork is designed correctly. We space the air outlets so each room receives equal cooling, and use dampers to control airflow to each zone.
Can I have separate thermostats for different rooms?
Yes, we can fit an advanced control system allowing separate temperature settings for each zone, but the extra cost depends on the number of areas and control type. Send us the details on WhatsApp.
Our building has higher ceilings, does that affect cooling efficiency?
Higher ceilings require a slightly more powerful outdoor unit to push cool air up effectively, but this does not significantly raise cost if the design is sound. We select the right capacity after inspecting your flat.
Can I add a second cooling zone later if needed?
We design ductwork with future expansion in mind if you wish to add a second zone later. But this depends on your outdoor unit's size and expandability, which we discuss with you before installation.
