Cooling fit for a mosque
Mosque HVAC in Al Shifa
In Al Shifa, south Jeddah, most mosques are modern with spacious halls accommodating large daily worshipper numbers. Alrabih designs powerful central cooling systems providing consistent coverage with energy efficiency.
- Even distribution
- Quiet units
- Scheduled servicing
Clients We're Proud to Serve
Organisations and companies that trusted Alrabih with their projects.
When a mosque needs a specialist approach
- 1
Heat reaching the back rows
Cold air pools near the units and never reaches the back of the hall. In Jeddah's humidity, worshippers in the far rows feel the heat even with the system running. That is a design problem, not a unit fault.
- 2
Noise that disturbs prayer
Unit noise in a quiet hall distracts worshippers and breaks concentration. The right unit type, its position and the air velocity setting all reduce noise to the lowest possible level, and those choices are made at the survey.
- 3
A dome or high ceiling that traps heat
Hot air rises and collects under the dome, so the breathing level stays warm even with large units running. We set diffuser angles and air paths at the survey to push that hot layer out rather than cool over the top of it.
Who it's for
Building a new mosque that needs AC from the start
We join the design stage to fix duct routes and unit positions before ceilings are closed, so the installation is clean and efficient with no remedial work needed later.
Ask on WhatsAppYour existing mosque cools unevenly across the rows
We survey the existing system, find the cause of uneven distribution and propose changes to the airflow paths or units without disrupting the mosque.
Ask on WhatsApp
What the work covers
- Hall survey and airflow mapping
- Ductwork to SMACNA standard
- Units fitted at surveyed positions
- Airflow check across the rows
- Contracts scheduled between prayers
How we work
How we work
- 1
Mosque survey
We visit the mosque outside prayer times to measure the hall, ceiling height and dome, and agree diffuser positions, duct routes and unit locations before any work begins.
- 2
Design and fabrication
We design the system from the survey data and fabricate the ducts in our own workshop from G90 galvanised sheet, then prepare them for installation.
- 3
Installation at agreed times
We coordinate with mosque management to work between prayers or at times that do not interrupt activities, and we leave the hall clean at the end of each working day.
- 4
Testing and handover
We run the system and measure air distribution at the front and back rows and sound levels, adjusting the balance until comfort is even across the whole hall.
Designed for a mosque or units placed at random?
| Alrabih | The usual way | |
|---|---|---|
| Air distribution | Even across every row | Cold front, hot back |
| Sound | Assessed at survey | Not considered |
| Dome and high ceiling | Planned airflow paths | Hot layer left above |
| Maintenance | Scheduled between prayers | Visits that disrupt use |
| Startup scheduling | Programmed before each prayer | Manual, inconsistent start |
Everything your AC needs, from one team
From system design and duct fabrication to installation, commissioning and maintenance.
Split AC installation
Request this serviceDuct installation
Request this serviceCentral AC installation
Request this serviceDuct fabrication
Request this serviceCold room installation
Request this serviceElectro-mechanical works
Request this serviceChiller & AHU installation
Request this serviceHVAC design
Request this serviceAC repair & faults
Request this serviceAC cleaning
Request this serviceRefrigerant charging
Request this serviceCentral AC maintenance
Request this serviceChiller maintenance
Request this serviceAC removal & refitting
Request this serviceDuct cleaning & sanitising
Request this serviceAC servicing by brand
Request this serviceOperation & maintenance contracts
Request this serviceAHU maintenance
Request this serviceFridge & freezer service
Request this serviceCold rooms
Request this serviceDisplay fridges & chillers
Request this serviceFactory HVAC
Request this serviceWarehouse HVAC
Request this serviceVilla & home HVAC
Request this serviceHotel HVAC
Request this serviceSchool HVAC
Request this serviceHospital HVAC
Request this serviceMosque HVAC
Request this serviceMall & retail HVAC
Request this serviceRestaurant & cafe HVAC
Request this service
Some of our work
Ductwork, rooftop units and diffusers, from work we've completed in Jeddah.
Customer reviews
What our customers say
- Muhammadramzan 2641
“MashaaAllah. Services are so good. Behaviour and kindness 100/100. Prices are less then Market. Fully recommended”
- shahzeb armani
“Wow. Prices are so comfortable. Outstanding services. People are so talented and nice”
- Tawfik AlyawerLocal Guide
“U can find all u need for air conditioning”
Your satisfaction matters to us! If you had a great experience with us, we'd love a 5-star rating and a kind review.
Worked with us? Leave a reviewService areas
We come to you anywhere in Jeddah
From Al Shiraa and Al Yaqout in the north to Al Thaghr and Al Quraiyat in the south, with our base in Al Aziziyah.
What sets this district apart
Al Shifa is a modern district with contemporary mosques featuring spacious prayer halls and high ceilings, drawing large congregations especially on Fridays and at sunset prayer. The area's high heat and coastal humidity place heavy thermal demands on the cooling system. Modern buildings offer better rooftop space for outdoor units, but the interior layout requires well-designed ducts to ensure no dead zones without cooling.
Al Shifa in south Jeddah is a modern district with contemporary mosques, spacious and high-ceilinged prayer halls.
Al Shifa mosques typically use central cooling systems with one or two outdoor units placed on the roof.
The AC setup in Al Shifa
- 1
Central system with one powerful outdoor unit
Large mosques in Al Shifa often use a single high-capacity outdoor unit placed on the spacious roof.
- 2
Central system with two balanced outdoor units
Very large mosques may use two balanced outdoor units to split the load and maintain efficiency.
- 3
Ceiling ducts with low-noise wall outlets
The design combines main ceiling ducts with low-noise wall outlets to reduce turbulence and noise.
Before the visit
Before our visit in Al Shifa
- 1
Inspect the roof and available space for units
Check roof area and the distance from roof to the hall interior, and confirm the structure can safely support heavy units.
- 2
Define duct and outlet locations inside
Discuss with administration and engineers where cold air outlets will sit in the hall to ensure even distribution and avoid noise and draughts.
- 3
Plan installation work well away from prayer times
Agree with administration on an installation schedule during light periods or specific days to minimise impact on daily activities.
More districts for Mosque HVAC
Other services in Al Shifa
FAQ
Questions about Mosque HVAC
How do you make sure the far rows get enough cooling?
At the survey we set diffuser angles, air velocity and duct routing so cold air travels to the last row. After installation we measure the temperature difference between the front and back rows and adjust each diffuser's balance until that difference is as small as the space allows.
Can you work in a functioning mosque without disrupting prayers?
Yes. We agree a phased schedule with mosque management in advance and divide the work into sessions between prayers. Before each call to prayer we lift tools, cover any temporary openings and return the hall to a usable state, then resume afterwards.
What type of ductwork do you use in prayer halls?
We fabricate ducts in our own workshop from G90 galvanised sheet, round or rectangular as the design requires. We use Armaflex and Kimmco insulation and Foster sealants to limit heat gain and keep sound transmission through the ductwork as low as possible.
Can the system be set to start just before each prayer time?
Yes. The controls on Carrier, YORK, General, Midea, Gree and Smart Gold units support scheduled start and stop times. At the survey we confirm the scheduling options for the chosen units and programme the timings at handover, so the hall is already cool when worshippers arrive.
Can we cool only part of the hall when fewer people attend?
Yes, if the system is designed in zones. We divide the hall into sections, each with its own unit or closable outlets, so you run the front rows alone when few people attend and the whole hall for Friday prayer and occasions, cutting power use without affecting worshippers.
How many outdoor units does a modern Al Shifa mosque need?
It depends on the hall size and capacity. We assess the area and thermal load and recommend either one powerful unit or two balanced units based on the design.
The street in front of the mosque is wide, does that ease installation?
Yes, the wide streets in Al Shifa make it easier to transport installation equipment and large units, and we agree on safe parking near the mosque entrance.
Worshipper numbers differ greatly between weekdays and Friday, does cooling efficiency suffer?
The system is sized for Friday capacity, but smart controls can be programmed to reduce power on lighter days, saving energy without compromising comfort.
Can ducts and outlets be cleaned without closing the mosque?
Regular maintenance and cleaning happen outside prayer times, and we coordinate with the administration to ensure daily mosque activities are unaffected.
