Moved without losing refrigerant
AC removal & refitting in Ghulail
In Ghulail, south Jeddah, AC relocation typically covers residential villas and small commercial units. Alrabih fully pumps the refrigerant before transport, then relocates both units and reinstalls them with new copper lines completely vacuumed.
- Refrigerant saved
- Fresh copper
- Holes sealed
Clients We're Proud to Serve
Organisations and companies that trusted Alrabih with their projects.
When you need removal and refitting
- 1
Moving to a new home
You want to take your units to the new home without losing the refrigerant charge or arriving with a unit that no longer cools properly. The right removal keeps the charge locked in the outdoor unit until refitting.
- 2
Renovation or repainting
Contractors need a clear wall for painting or plastering. We remove the indoor unit after saving the refrigerant, and once the renovation is done, we refit and close old holes that would otherwise spoil the fresh wall finish.
- 3
Repositioning a unit in the same building
The current position may no longer suit new furniture, or the old wall core is in the wrong place. We move it to the better spot and plan the new copper and drain route before drilling anything.
Who it's for
Renovating your flat and need walls cleared
We remove indoor units after pump-down, seal old holes, then refit once finishing work is complete so your units are never handled by the renovation crew.
Ask on WhatsAppRelocating your business to new premises
We survey both premises, pump down, remove the units from the current site, then refit them at the new location with copper runs and drain lines suited to the new building layout.
Ask on WhatsApp
What the service covers
- Pump-down into outdoor unit
- Remove both units cap pipes
- Seal old wall holes
- Mueller copper insulated on site
- Vacuum test and start-up
How we work
How we work
- 1
Survey both sites
We visit the removal site and the new location to plan the copper route, drain line and run length, and tell you if new copper or extra materials are needed.
- 2
Pump down and remove
We run the unit in pump-down mode until all refrigerant moves into the outdoor unit, then close the service valves and remove both units carefully.
- 3
Seal holes and transport
We close the old wall cores with suitable material so they do not let in hot air or insects, then transport both units to the new location.
- 4
Refit, vacuum and start
We mount both units, run Mueller copper in runs of up to 30 metres without welded joints, vacuum the line, test the joints, then release the saved refrigerant and verify cooling with you present.
Proper removal or an unprepared one?
| Alrabih | The usual way | |
|---|---|---|
| Refrigerant | Saved by pump-down | Lost to the air |
| Copper pipes | Capped at removal | Open, moisture enters |
| Old holes | Sealed after removal | Left open, air leaks in |
| New-site copper | New Mueller, insulated | Old copper reused |
| Drain at new site | Drain fall planned at survey | Left to chance during fitting |
Everything your AC needs, from one team
From system design and duct fabrication to installation, commissioning and maintenance.
Split AC installation
Request this serviceDuct installation
Request this serviceCentral AC installation
Request this serviceDuct fabrication
Request this serviceCold room installation
Request this serviceElectro-mechanical works
Request this serviceChiller & AHU installation
Request this serviceHVAC design
Request this serviceAC repair & faults
Request this serviceAC cleaning
Request this serviceRefrigerant charging
Request this serviceCentral AC maintenance
Request this serviceChiller maintenance
Request this serviceAC removal & refitting
Request this serviceDuct cleaning & sanitising
Request this serviceAC servicing by brand
Request this serviceOperation & maintenance contracts
Request this serviceAHU maintenance
Request this serviceFridge & freezer service
Request this serviceCold rooms
Request this serviceDisplay fridges & chillers
Request this serviceFactory HVAC
Request this serviceWarehouse HVAC
Request this serviceVilla & home HVAC
Request this serviceHotel HVAC
Request this serviceSchool HVAC
Request this serviceHospital HVAC
Request this serviceMosque HVAC
Request this serviceMall & retail HVAC
Request this serviceRestaurant & cafe HVAC
Request this service
Some of our work
Ductwork, rooftop units and diffusers, from work we've completed in Jeddah.
Customer reviews
What our customers say
- Muhammadramzan 2641
“MashaaAllah. Services are so good. Behaviour and kindness 100/100. Prices are less then Market. Fully recommended”
- shahzeb armani
“Wow. Prices are so comfortable. Outstanding services. People are so talented and nice”
- Tawfik AlyawerLocal Guide
“U can find all u need for air conditioning”
Your satisfaction matters to us! If you had a great experience with us, we'd love a 5-star rating and a kind review.
Worked with us? Leave a reviewService areas
We come to you anywhere in Jeddah
From Al Shiraa and Al Yaqout in the north to Al Thaghr and Al Quraiyat in the south, with our base in Al Aziziyah.
What sets this district apart
Ghulail is a mid-range residential district with villas, small shops and simple apartment blocks. Residents here move frequently, and units are either left at the first home or relocated to a new site. Distances between indoor and outdoor units are typically moderate, but when shops are involved we coordinate with owners. The southern location means high exposure to heat and dust, so we choose a protected spot for the outdoor unit.
Ghulail is a mid-range residential district in south Jeddah, mixing villas, small apartment blocks and modest shops with moderate building density.
Most units here are splits, with typical copper runs between 8 and 15 metres, though some shops may need shorter lines.
The AC setup in Ghulail
- 1
One split per villa or shop
Each unit serves one villa or shop independently, so relocation is straightforward but requires calculating the new distance.
- 2
Moderate copper runs
Indoor-to-outdoor distance is typically 8 to 15 metres, but may increase if the owner chooses a farther spot.
- 3
Protection from heat and dust
The southern location means choosing shade or a cover for the outdoor unit and good insulation for the copper lines.
Before the visit
Before our visit in Ghulail
- 1
Confirm the new outdoor unit location
Choose a spot shaded from direct sun and dust, and ensure it is accessible for maintenance and cleaning.
- 2
Survey distance and power routing
Measure the distance from the new indoor location to the outdoor spot, and map the routing for power and copper lines clearly.
- 3
Coordinate with shop owner or landlord
If relocating a shop unit or rental property, confirm the shop owner or landlord approves the new location before booking.
More districts for AC removal & refitting
Other services in Ghulail
FAQ
Questions about AC removal & refitting
Can the old copper pipes be reused at the new site?
It depends on the condition of the pipes and the layout at the new site. If the pipes are free of oxidation and insulation cracking, and the length fits the new run, they can be reused after inspection. If the new site needs a longer route or the existing pipes show wear, fresh Mueller copper pipe at 99% pure copper is run to suit the new layout. The site survey decides.
Why not just remove the unit without pumping down first?
Before any connection is opened, the compressor is run to pump the refrigerant charge into the outdoor unit and the service valves are closed on it. If the connections are opened first, the refrigerant escapes into the air and is lost entirely, which is both costly and harmful to the environment. Pumping down first keeps the full charge sealed inside the outdoor unit, ready to use at the new site.
What happens to the old wall hole after the unit is removed?
Once the pipes and cable are pulled out, the hole is cleared of insulation remnants and sleeve material, then sealed with a filler suited to the wall type, whether concrete, brick or gypsum board. The aim is a tight closure that stops humid air and insects from entering and leaves the wall surface clean before the site is handed back.
Can a unit be moved to a different floor in the same building?
Yes, but moving to a different floor means a completely new pipe route, a different cable length, and possibly a changed drain line fall. The site survey defines the pipe path, the required run length and the outdoor unit position. Mueller copper pipe at 99% pure copper is then laid along a route that accounts for the floor difference, and a vacuum test and pressure test are carried out before the unit is started.
Can a unit be moved to a different floor in the same building?
Yes, but a different floor changes the copper run length, the drain route and where the outdoor unit is fixed. At the survey we establish whether extra copper is needed and where the drain can fall correctly, then plan the full route before any removal begins.
I own a small shop and want to move the AC to another spot, how do you handle this?
We remove the unit from the first location by pumping the refrigerant, then relocate it and coordinate with your new shop location or another corner of the current shop. We install new copper lines to fit and test everything fully.
Heat in Ghulail is intense, does the new outdoor location affect cooling efficiency?
Yes, we choose a spot shaded from direct sun if possible, such as under a staircase, awning, or the north side of the building, to improve cooling efficiency.
My shop is on a corner, can the outdoor unit be installed at a distance away?
Yes, we run new copper lines from the indoor unit to the new location at the required length, vacuum the lines and test pressure and airflow fully.
Ghulail has southern humidity and dust, does the new unit need extra protection?
We choose a spot protected from dust and moisture as much as possible, use strong insulation for copper lines, and recommend regular filter and evaporator coil cleaning.
