Cold rooms kept running
Cold rooms in Kinanah
In Kinanah, east Jeddah, shops, restaurants and small warehouses rely on robust yet straightforward cold rooms. Alrabih balances performance efficiency and affordable maintenance by servicing the evaporator, seals and controls.
- Accurate diagnosis
- Clean evaporator
- Sealed door
Clients We're Proud to Serve
Organisations and companies that trusted Alrabih with their projects.
When your cold room needs attention
- 1
Room not holding temperature
The temperature climbs slowly even though the unit keeps running, or the products inside are warmer than they should be. The cause could be the evaporator, condensing unit, refrigerant level or controller, and only a site check tells which.
- 2
Evaporator icing up and stopping
Ice builds on the evaporator until airflow stops and cooling fails. The cause is usually in the defrost circuit, its sensor or the evaporator fan. Jeddah's humid air speeds up icing when anything in that circuit is not working correctly.
- 3
Door letting cold air escape
A worn or deformed door seal lets warm humid air in, overloading the refrigeration unit and speeding up evaporator icing. If the door frame heater has failed, moisture builds on the frame and the door becomes hard to open.
Who it's for
Running a restaurant or central kitchen cold room
We check the evaporator, defrost circuit and door seal in your kitchen cold room and fix any fault before your food stock is put at risk.
Ask on WhatsAppOperating a freezer room in a warehouse or retail outlet
We find the cause of temperature loss in your freezer room, inspect the rooftop condensing unit, controller and alarm, and complete a full running test before we leave.
Ask on WhatsApp
What the service covers
- Evaporator check and clean
- Defrost circuit and sensors
- Door seal and frame heater
- Rooftop condensing unit inspection
- Controller and temperature alarm
How we work
How we work
- 1
Describe the fault
WhatsApp us what you see: the temperature showing on the controller, whether the unit is running or not, and the type of stock inside the room.
- 2
Site check and diagnosis
The technician checks the evaporator, condensing unit, defrost circuit, controller and door seal, then identifies the actual cause of the temperature loss before starting any work.
- 3
Repair and replacement
We fix what the diagnosis found: clean the evaporator, repair the defrost circuit, replace the seal or adjust the refrigerant charge to the type written on the unit nameplate.
- 4
Test and handover
We run the room and watch the temperature until it reaches the set value, confirm the alarm and controller are working, then hand you a report of what was done.
Systematic maintenance or a quick temporary fix?
| Alrabih | The usual way | |
|---|---|---|
| Diagnosis | Root cause first | Symptom fixed only |
| Evaporator | Checked and cleaned | Ignored until it stops |
| Door seal | Checked, adjusted or replaced | Left until obviously leaking |
| Controller and alarm | Tested before leaving | Not checked |
| Post-visit report | Written record of work done | Verbal summary only |
Everything your AC needs, from one team
From system design and duct fabrication to installation, commissioning and maintenance.
Split AC installation
Request this serviceDuct installation
Request this serviceCentral AC installation
Request this serviceDuct fabrication
Request this serviceCold room installation
Request this serviceElectro-mechanical works
Request this serviceChiller & AHU installation
Request this serviceHVAC design
Request this serviceAC repair & faults
Request this serviceAC cleaning
Request this serviceRefrigerant charging
Request this serviceCentral AC maintenance
Request this serviceChiller maintenance
Request this serviceAC removal & refitting
Request this serviceDuct cleaning & sanitising
Request this serviceAC servicing by brand
Request this serviceOperation & maintenance contracts
Request this serviceAHU maintenance
Request this serviceFridge & freezer service
Request this serviceCold rooms
Request this serviceDisplay fridges & chillers
Request this serviceFactory HVAC
Request this serviceWarehouse HVAC
Request this serviceVilla & home HVAC
Request this serviceHotel HVAC
Request this serviceSchool HVAC
Request this serviceHospital HVAC
Request this serviceMosque HVAC
Request this serviceMall & retail HVAC
Request this serviceRestaurant & cafe HVAC
Request this service
Some of our work
Ductwork, rooftop units and diffusers, from work we've completed in Jeddah.
Customer reviews
What our customers say
- Muhammadramzan 2641
“MashaaAllah. Services are so good. Behaviour and kindness 100/100. Prices are less then Market. Fully recommended”
- shahzeb armani
“Wow. Prices are so comfortable. Outstanding services. People are so talented and nice”
- Tawfik AlyawerLocal Guide
“U can find all u need for air conditioning”
Your satisfaction matters to us! If you had a great experience with us, we'd love a 5-star rating and a kind review.
Worked with us? Leave a reviewService areas
We come to you anywhere in Jeddah
From Al Shiraa and Al Yaqout in the north to Al Thaghr and Al Quraiyat in the south, with our base in Al Aziziyah.
What sets this district apart
Kinanah is an emerging commercial zone with diverse food shops, small warehouses, local restaurants and small food processing facilities. Buildings here are relatively modern with practical straightforward design, and spaces are wider than older districts. Cold rooms range from simple to mid-sized units with good efficiency. Eastern heat is moderate and humidity lower than coastal areas, but dust from rising industrial activity needs regular cleaning. Access to units is straightforward and coordination with management is direct.
Kinanah lies in east Jeddah as an emerging commercial zone with small shops, warehouses and food processing facilities.
Cold rooms here range from simple to mid-sized units with wall-mounted evaporators and outdoor units on roofs or back walls.
The AC setup in Kinanah
- 1
Simple to mid-sized unit with wall evaporator
Most small shops and warehouses use simple units with wall-mounted evaporators in the storage room.
- 2
Outdoor unit on roof or back wall
Outdoor units are typically mounted on roofs or rear walls facing back lanes or open space.
- 3
Standard rubber seals
Seals are standard and basic but need regular replacement, especially in dusty environments.
Before the visit
Before our visit in Kinanah
- 1
Agree on the best access route
If the warehouse is set back from the main road or in a narrow lane, give us location details and the best approach route.
- 2
Confirm safe roof access
If the outdoor unit is on the roof, check that roof access is safe, easy to open and not blocked or barred.
- 3
Coordinate with warehouse management on timing
Give them at least a week's notice so they can prepare and avoid clashing with loading or unloading operations.
More districts for Cold rooms
Other services in Kinanah
FAQ
Questions about Cold rooms
Why does the temperature rise even though the unit runs all the time?
Continuous running does not mean correct operation. Common causes include a refrigerant leak that reduces the charge, heavy frost on the evaporator coil blocking airflow, or a fault in the rooftop condensing unit raising head pressure. A site survey identifies the actual cause before any work begins.
How do I know if the defrost cycle is working properly?
Clear signs of a defrost fault include thick frost covering the full evaporator coil, a gradual temperature rise while the unit keeps running, and water pooling on the floor instead of draining away. The check covers the heater element, the defrost sensor and the controller, as the fault can lie in any of these parts.
What does a preventive visit for a cold room cover?
A preventive visit covers a pressure check on the refrigeration circuit, cleaning the condenser and evaporator coils, inspecting door seals and frame heaters, testing the controller and alarm, and checking copper pipe connections. The aim is to find a developing fault before it affects the room temperature and the stock inside.
What is the difference between a preventive visit and a repair visit?
A preventive visit is carried out on a unit that is running normally: the purpose is inspection, cleaning and finding early signs of wear before they become a breakdown. A repair visit is requested when an actual fault appears, such as a rising temperature, a stopped compressor or excessive coil icing. Diagnosis comes first, then the required work is defined.
Does Jeddah's rooftop heat affect the condensing unit's performance?
Yes. In summer, Jeddah rooftop surfaces reach very high temperatures, which raises condensing pressure, stresses the compressor and reduces cooling capacity. Regular cleaning of the condenser coil to remove the dust and salt that cling to the fins is essential, not optional. A site survey determines whether the unit's position or the airflow around it is making the problem worse.
The room runs but does not get as cold as before, is the fault in the seals or evaporator?
It could be seal wear, ice buildup on the evaporator, or refrigerant leakage. We inspect the seals, evaporator and pressure to pinpoint the cause accurately.
The warehouse is set back from the main road with a narrow entry lane, can you get the team there?
Yes, we're equipped for remote areas and narrow lanes. We agree on a safe entry point and can reach you easily.
Dust from nearby factories clogs the coils, how often should we clean?
In industrial areas like Kinanah, we recommend cleaning every three to four months to maintain performance and prevent breakdowns.
Can you service the room at night after the warehouse closes?
We work Saturday to Thursday, 8 am to 8 pm. We can schedule close to closing time if needed.
