Dedicated duct workshop
Duct fabrication in Al Tha'alibah
Duct fabrication in Al Tha'alibah, south Jeddah, demands precision because the modern residential and hotel buildings need complex air runs. We fabricate rectangular and round duct in our workshop from galvanized or aluminium sheet to site dimensions or drawings, so it arrives ready to hang with no air loss.
- G90 sheet
- Site dimensions
- Complex fittings
Clients We're Proud to Serve
Organisations and companies that trusted Alrabih with their projects.
Who needs workshop-fabricated duct?
- 1
A contractor with project-specific sizes
Your project has non-standard sizes or volumes too large for site cutting. We fabricate rectangular and round sections from your drawings at exact dimensions, labelled and ready to hang when they reach the site.
- 2
Fittings too awkward to cut on site
Elbows, transitions, offsets and takeoffs come out distorted when cut by hand on site, leaking air and creating noise in the line. We make them in the workshop at the right dimensions with tight seams.
- 3
Extending or renovating an existing duct network
You need new branches, a damaged section replaced or a fitting that matches an old duct size. We measure the existing network on site and fabricate the pieces to match what is already there.
Who it's for
Building a facility that needs non-standard duct sizes
We read your project drawings and fabricate all sections and fittings at exact dimensions from G90 or aluminium sheet, labelled and ready to hang the moment they reach your site.
Ask on WhatsAppRenovating home AC and need fittings to match old duct
We measure the existing ductwork in your home and fabricate the branches, transitions and elbows needed to match the original duct without replacing the whole network.
Ask on WhatsApp
What the fabrication covers
- Site measure or drawings
- G90 or aluminium duct
- Elbows transitions and takeoffs
- Tight seams to SMACNA
- Labelled sections ready to hang
How we work
How we work
- 1
Take measurements
A technician visits the site or you send us the drawings; we list every duct section needed, its size and the correct sheet thickness for that section.
- 2
Fabricate sections and fittings
We cut, form and lock the sheet in the workshop, including all elbows, transitions, offsets and takeoffs, and each section comes out at its exact dimension.
- 3
Label and prepare for delivery
We number every section and fitting against the assembly plan so the installation crew knows exactly where each piece goes, with no guessing on site.
- 4
Deliver to site
We deliver the duct to your Jeddah site protected and ready to hang. If you need an installation crew, we can arrange that as a separate step.
Workshop fabrication or site cutting?
| Alrabih | The usual way | |
|---|---|---|
| Dimensional accuracy | Workshop machines, tight dims | Hand variation on site |
| Complex fittings | Correct elbows and transitions | Distorted, leaking air |
| Seam quality | Tight lock, low leakage | Gaps weaken pressure |
| Site schedule | Arrives ready to hang | Extra time and site noise |
| Salt and humidity | Aluminium where site demands | One sheet regardless |
Everything your AC needs, from one team
From system design and duct fabrication to installation, commissioning and maintenance.
Split AC installation
Request this serviceDuct installation
Request this serviceCentral AC installation
Request this serviceDuct fabrication
Request this serviceCold room installation
Request this serviceElectro-mechanical works
Request this serviceChiller & AHU installation
Request this serviceHVAC design
Request this serviceAC repair & faults
Request this serviceAC cleaning
Request this serviceRefrigerant charging
Request this serviceCentral AC maintenance
Request this serviceChiller maintenance
Request this serviceAC removal & refitting
Request this serviceDuct cleaning & sanitising
Request this serviceAC servicing by brand
Request this serviceOperation & maintenance contracts
Request this serviceAHU maintenance
Request this serviceFridge & freezer service
Request this serviceCold rooms
Request this serviceDisplay fridges & chillers
Request this serviceFactory HVAC
Request this serviceWarehouse HVAC
Request this serviceVilla & home HVAC
Request this serviceHotel HVAC
Request this serviceSchool HVAC
Request this serviceHospital HVAC
Request this serviceMosque HVAC
Request this serviceMall & retail HVAC
Request this serviceRestaurant & cafe HVAC
Request this service
Some of our work
Ductwork, rooftop units and diffusers, from work we've completed in Jeddah.
Customer reviews
What our customers say
- Muhammadramzan 2641
“MashaaAllah. Services are so good. Behaviour and kindness 100/100. Prices are less then Market. Fully recommended”
- shahzeb armani
“Wow. Prices are so comfortable. Outstanding services. People are so talented and nice”
- Tawfik AlyawerLocal Guide
“U can find all u need for air conditioning”
Your satisfaction matters to us! If you had a great experience with us, we'd love a 5-star rating and a kind review.
Worked with us? Leave a reviewService areas
We come to you anywhere in Jeddah
From Al Shiraa and Al Yaqout in the north to Al Thaghr and Al Quraiyat in the south, with our base in Al Aziziyah.
What sets this district apart
Al Tha'alibah is a relatively modern district with tall residential towers, hotels and widely spaced office blocks on open land, so central AC projects here need long, complex duct runs between floors and suites, and each bend and junction must be made to precision. On-site cutting does not hold proper dimensions and causes air leaks at joints, so we fabricate it in the workshop to the plan and ensure a tight fit and performance.
Al Tha'alibah lies in south Jeddah, a district of modern residential, hotel and commercial buildings set on relatively open land.
Most residential and hotel towers here use central AC systems with rectangular or round duct routed through the floors.
The AC setup in Al Tha'alibah
- 1
Rectangular duct for residential towers
Residential towers in Al Tha'alibah use wide rectangular duct to distribute air across suites and corridors with high efficiency.
- 2
Round duct for hotels and offices
Hotels and commercial buildings here use round duct because it allows complex horizontal and vertical turns through the floors.
- 3
Complex transitions and elbows
Large projects here need custom transition pieces and non-standard elbows between equipment and variable spaces, which we fabricate precisely in the workshop.
Before the visit
Before our visit in Al Tha'alibah
- 1
Obtain the full architectural drawing
Before the visit, send us the precise architectural drawing of the tower or hotel so we can measure the duct accurately and fabricate it without error.
- 2
Confirm location of main AC units
Confirm where the main AC equipment sits, whether in a plant room or on the roof, since the start and end points of the duct runs determine all dimensions.
- 3
Agree schedule with the contractor
Agree with the contractor and team on the visit and measurement date, so we can prepare the duct in line with the construction schedule.
More districts for Duct fabrication
Other services in Al Tha'alibah
FAQ
Questions about Duct fabrication
Can you fabricate from drawings without visiting the site?
Yes, when the drawings are clear and carry the actual as-built dimensions. If a dimension is uncertain or a field change has been made, we prefer a site visit to avoid a fabricated piece that does not fit. We discuss the better approach with you before starting work.
What is the difference between galvanized and aluminium sheet for duct?
G90 galvanized sheet is the standard choice for interior duct: strong and suited to a range of pressures. Aluminium is lighter and handles Jeddah's coastal humidity and salt air better, making it right for some exposed applications or where structural load is a limiting factor. The correct choice depends on the site.
Can you make elbows and transitions to match an existing duct network?
Yes. We measure the existing network on site to match sizes precisely, whether you need a new branch added, a damaged fitting replaced or an extension tied into the original ductwork. The right approach is confirmed after the site visit.
How do you choose sheet thickness for each section?
Thickness follows section size: a large duct needs heavier sheet to hold its shape under pressure, a small one can use lighter material. We apply the SMACNA requirements to each section in the project individually, not a single thickness across the whole job.
Does Jeddah's humidity and salt air affect which sheet material to use?
Yes, particularly for sections exposed to outdoor air or installed near fresh-air intakes. G90 galvanized sheet performs well inside the building, but aluminium is the better choice where duct is in continuous contact with Jeddah's humid, salt-laden air. The site survey determines the right material for each section.
Why not cut the duct on site directly?
On-site cutting cannot hold precise dimensions and cannot produce complex elbows and offsets properly. In the workshop we fabricate it to the plan, so it arrives ready to hang with no air loss at the joints.
Our project spans multiple floors, how do you get the duct in?
We measure the duct to site drawings or architectural plans, and fabricate it in ready-made sections that fit the building passages and floor gaps, so it enters easily and assembles to exact fit.
Hotels and towers here need high-precision AC, how do you ensure that?
We use G90 galvanized or aluminium sheet and produce duct with precise elbows, offsets and takeoffs to the drawing, which keeps the airflow even and airtight when assembled.
How long does duct fabrication take?
The time depends on the project size, number of sections and complexity of the runs. We agree the schedule with the contractor after reviewing the plan and site.
