Freezer and dual-temp rooms
Cold & freezer room installation in Al Harrah
Cold and freezer room installation in Al Harrah serves restaurants and food warehouses needing reliable storage for meat, fish and frozen goods in a district of mixed building types. Alrabih's team designs the room with tight insulation and a strong frost and moisture-resistant floor.
- Frost-proof floor
- Auto defrost
- Two-zone layout
Clients We're Proud to Serve
Organisations and companies that trusted Alrabih with their projects.
Who needs a specialist freezer room?
- 1
Stock that needs sub-zero cold
Meat, poultry, fish and ice cream spoil if the temperature rises even briefly above the required level. A freezer room is built to hold that level continuously, not simply to cool.
- 2
One room, two temperature zones
Large restaurants and hotels usually need a chiller section and a freezer section side by side. We build both wings with separate insulation, independent refrigeration units and an insulated inner door, so neither zone affects the other's temperature.
- 3
Expanding an existing facility
If your current cold room no longer holds all your stock, or you need to add a freezer section beside it, we survey the site and propose the most practical way to expand with as little disruption to your operation as possible.
Who it's for
Opening a restaurant that needs a freezer room
We survey your kitchen and build the freezer room with frost-rated insulation panels, an insulated floor and a tight-sealing door.
Ask on WhatsAppNeed a chiller wing and a freezer wing together
We build both wings with separate insulation, independent refrigeration units and an insulated inner door between them.
Ask on WhatsApp
What the installation covers
- Freezer-rated insulation panels
- Insulated floor vapour barrier
- Heated frame tight-sealing door
- Evaporator with electric defrost
- Condensing unit temperature controller
How we work
How we work
- 1
Site survey
We visit the site, learn the stock type and required temperature, measure the available space, and decide the right insulation thickness and refrigeration system from what we find.
- 2
Design and supply
We draw the room layout including pipe and cable routes, then have the panels, doors and equipment ready before installation begins.
- 3
Installation and connection
We fit the panels, insulated floor and door, then run and insulate the copper pipes, vacuum the line and pressure-test it before starting the system. Mueller copper in runs of up to 30 metres without welded joints where the layout calls for it.
- 4
Start-up and handover
We run the system and watch the room reach its target temperature, confirm the defrost cycle works and the door seals properly, then explain the controls to the person responsible for the facility.
Specialist install or an unconsidered one?
| Alrabih | The usual way | |
|---|---|---|
| Floor | Insulated with vapour barrier | Plain floor that cracks |
| Door frame | Heated to prevent seizure | Freezes and warps |
| Evaporator | Scheduled electric defrost | Ice blocks the airflow |
| Insulation | Thickness set at survey | Same thickness for every room |
| Anteroom | Buffer zone reduces air ingress | Direct door into freezer |
Everything your AC needs, from one team
From system design and duct fabrication to installation, commissioning and maintenance.
Split AC installation
Request this serviceDuct installation
Request this serviceCentral AC installation
Request this serviceDuct fabrication
Request this serviceCold room installation
Request this serviceElectro-mechanical works
Request this serviceChiller & AHU installation
Request this serviceHVAC design
Request this serviceAC repair & faults
Request this serviceAC cleaning
Request this serviceRefrigerant charging
Request this serviceCentral AC maintenance
Request this serviceChiller maintenance
Request this serviceAC removal & refitting
Request this serviceDuct cleaning & sanitising
Request this serviceAC servicing by brand
Request this serviceOperation & maintenance contracts
Request this serviceAHU maintenance
Request this serviceFridge & freezer service
Request this serviceCold rooms
Request this serviceDisplay fridges & chillers
Request this serviceFactory HVAC
Request this serviceWarehouse HVAC
Request this serviceVilla & home HVAC
Request this serviceHotel HVAC
Request this serviceSchool HVAC
Request this serviceHospital HVAC
Request this serviceMosque HVAC
Request this serviceMall & retail HVAC
Request this serviceRestaurant & cafe HVAC
Request this service
Some of our work
Ductwork, rooftop units and diffusers, from work we've completed in Jeddah.
Customer reviews
What our customers say
- Muhammadramzan 2641
“MashaaAllah. Services are so good. Behaviour and kindness 100/100. Prices are less then Market. Fully recommended”
- shahzeb armani
“Wow. Prices are so comfortable. Outstanding services. People are so talented and nice”
- Tawfik AlyawerLocal Guide
“U can find all u need for air conditioning”
Your satisfaction matters to us! If you had a great experience with us, we'd love a 5-star rating and a kind review.
Worked with us? Leave a reviewService areas
We come to you anywhere in Jeddah
From Al Shiraa and Al Yaqout in the north to Al Thaghr and Al Quraiyat in the south, with our base in Al Aziziyah.
What sets this district apart
Al Harrah is medium-density with residential blocks, commercial shops and several small restaurants and medium food warehouses. Buildings here vary in age and type: some modern, some older, meaning foundation and electrical requirements differ. Coastal humidity and extreme summer heat make a strong floor and thick insulation essential for room efficiency. Outdoor unit space may be limited in older buildings, so design flexibility is needed.
Al Harrah lies in north-east Jeddah, a district of mixed buildings from older residential blocks to modern shops and restaurants.
Freezer rooms in the restaurants and warehouses here range from 5 to 12 square metres, and usually need cooling units with 2 to 3.5 tonnes capacity.
The AC setup in Al Harrah
- 1
Single-temperature freezer for small restaurants
Small restaurants and medium warehouses here usually need one freezer room at -18 to -25°C without internal division.
- 2
Room with internal partition for chilling and freezing
Some medium restaurants benefit from one internal partition separating a 2-4°C chiller zone from a lower-temperature freezer zone.
- 3
Outdoor unit on roof or exterior wall
The outdoor unit is roof-mounted in modern buildings or wall-mounted on a strong exterior wall in older buildings based on space and structural capacity.
Before the visit
Before our visit in Al Harrah
- 1
Inspect foundation, soil and moisture
Inspect the foundation, floor and soil around the building, and tell us if there is any moisture or seepage before the visit day.
- 2
Check roof or wall strength for outdoor unit
Confirm the roof (in modern buildings) or exterior wall (in older buildings) is strong enough to support the outdoor unit's weight.
- 3
Confirm unit location and electrical runs
Decide on the outdoor unit location (roof or wall) and confirm there is nearby power and safe space for copper runs.
More districts for Cold & freezer room installation
Other services in Al Harrah
FAQ
Questions about Cold & freezer room installation
Why does a freezer room need an insulated floor when a chiller often does not?
At sub-zero temperatures the moisture held in a concrete slab freezes and expands, cracking tiles and lifting bases over time. A chiller room operates above freezing, so ice crystals do not form in the slab. A freezer room therefore requires insulated panels under the floor together with a vapour barrier that blocks rising ground heat and protects the structure over the long term.
What is the difference between electric defrost and other types?
Electric defrost uses heating elements fixed inside the evaporator coil; they warm the coil directly and melt frost build-up. Hot-gas defrost instead redirects warm refrigerant from the compressor back through the same coil. The choice between the two depends on room size, the required number of cycles and the type of goods stored; the site survey determines which method suits each installation.
Can two zones at different temperatures share the same footprint?
Yes. A partition of insulated panels separates the space, with each side using a panel thickness matched to its required temperature differential. Each zone has its own refrigeration unit and a door with a heated frame to prevent condensation. This arrangement is widely used in meat and fish facilities that need a chiller zone for short-term stock and a freezer zone for longer storage. The final design depends on the available floor area and the heat load of each section.
Does the position of the condensing unit affect how the freezer room performs?
Position has a direct effect. The condensing unit needs clean air and adequate flow to reject heat; if it is placed in a confined space or near heat sources the condensing pressure rises and the compressor works harder. In Jeddah, outdoor air also carries salt and dust that accumulate on the condenser coil over time. The site survey identifies the best location and the copper-pipe route, keeping each Mueller copper pipe run within thirty metres without welded joints.
Does the position of the condensing unit affect how the freezer room performs?
Position has a direct effect. The condensing unit needs clean air and adequate flow to reject heat; if it is placed in a confined space or near heat sources the condensing pressure rises and the compressor works harder. In Jeddah, outdoor air also carries salt and dust that accumulate on the condenser coil over time. The site survey identifies the best location and the copper-pipe route, keeping each Mueller copper pipe run within thirty metres without welded joints.
My restaurant is in an older building, can a freezer room be installed there?
Yes, but we inspect the foundation and floor first. Older buildings may need foundation reinforcement or extra moisture protection before installation, which does not greatly affect final cost.
My warehouse has a low roof, can the outdoor unit go on the wall instead?
Yes, it can be wall-mounted on a strong exterior wall. We check wall strength and water drainage from the unit, and side-mounting is often a good solution for low-roof buildings.
Humidity and heat are very high here, how often does the room need maintenance?
Coastal humidity and heat increase evaporator and condenser stress. We recommend maintenance every three months to clean coils, filters and the outdoor fan.
The wiring is old, does it need upgrading before installation?
We inspect the wiring and advise if safe upgrades are needed. Most older buildings in Al Harrah need at least a new dedicated circuit for the room.
