Medical facility HVAC
Hospital HVAC in North Corniche
On the North Corniche, hospitals and specialist clinics need reliable cooling that never stops, especially in theatres and intensive care. Alrabih designs systems to fit each department's needs and carries out maintenance without halting patient care.
- Per-department ventilation
- Maintenance without shutdown
- Survey-based design
Clients We're Proud to Serve
Organisations and companies that trusted Alrabih with their projects.
When you need a medical HVAC specialist
- 1
Hospital or clinic under construction
The right design starts before any duct is installed, because ventilation and filtration needs differ from the surgical suite to the waiting area. An early survey saves costly alterations after the building is finished.
- 2
Departments reporting warm air or odours
In an existing medical building, weak cooling in one department or odours crossing into an adjacent area signals an imbalance in the air distribution or extraction system. Finding the cause needs measurement, not guesswork.
- 3
Maintenance contract for a running facility
A hospital does not close for equipment servicing. We schedule preventive maintenance visits department by department, coordinated with facility management, and carry out repairs with the smallest possible effect on daily operations.
Who it's for
Building a new hospital or medical centre
We survey the building early and design systems to each department's requirements before installation begins.
Ask on WhatsAppYour clinic has repeated cooling faults
We inspect the existing systems, find the root cause of recurring faults, and repair them without stopping the clinic.
Ask on WhatsApp
What the service covers
- Building survey and requirements
- Duct network and AHU design
- Installation commissioning and testing
- Preventive and corrective contracts
- Maintenance without stopping departments
How we work
How we work
- 1
Survey and requirements
We visit the facility, map the heat loads and air requirements for each department, and agree the duct routes before any design work begins.
- 2
Design and supply
We design the duct network and fabricate it in our own workshop to SMACNA specifications, and supply units from our authorised brands: Carrier, YORK, General, Midea, Gree and Smart Gold.
- 3
Phased coordinated installation
In operating buildings we work with management to phase the installation so adjacent departments stay open, and control dust and noise away from patient areas.
- 4
Commissioning and follow-up
We commission the systems, measure airflow in each department, and adjust the dampers until the design requirements are met, then hand over the facility with a maintenance plan.
Survey-based design or an off-the-shelf solution?
| Alrabih | The usual way | |
|---|---|---|
| Design basis | Each department surveyed separately | One solution for the whole building |
| Ventilation and extract | Tailored to each space's function | Unbalanced between departments |
| Maintenance | Without closing departments | Full work stoppage |
| Ductwork | Fabricated in-house to SMACNA spec | Off-the-shelf non-compliant ducts |
| Copper runs | Mueller, no welded joints | Many welded joints |
Everything your AC needs, from one team
From system design and duct fabrication to installation, commissioning and maintenance.
Split AC installation
Request this serviceDuct installation
Request this serviceCentral AC installation
Request this serviceDuct fabrication
Request this serviceCold room installation
Request this serviceElectro-mechanical works
Request this serviceChiller & AHU installation
Request this serviceHVAC design
Request this serviceAC repair & faults
Request this serviceAC cleaning
Request this serviceRefrigerant charging
Request this serviceCentral AC maintenance
Request this serviceChiller maintenance
Request this serviceAC removal & refitting
Request this serviceDuct cleaning & sanitising
Request this serviceAC servicing by brand
Request this serviceOperation & maintenance contracts
Request this serviceAHU maintenance
Request this serviceFridge & freezer service
Request this serviceCold rooms
Request this serviceDisplay fridges & chillers
Request this serviceFactory HVAC
Request this serviceWarehouse HVAC
Request this serviceVilla & home HVAC
Request this serviceHotel HVAC
Request this serviceSchool HVAC
Request this serviceHospital HVAC
Request this serviceMosque HVAC
Request this serviceMall & retail HVAC
Request this serviceRestaurant & cafe HVAC
Request this service
Some of our work
Ductwork, rooftop units and diffusers, from work we've completed in Jeddah.
Customer reviews
What our customers say
- Muhammadramzan 2641
“MashaaAllah. Services are so good. Behaviour and kindness 100/100. Prices are less then Market. Fully recommended”
- shahzeb armani
“Wow. Prices are so comfortable. Outstanding services. People are so talented and nice”
- Tawfik AlyawerLocal Guide
“U can find all u need for air conditioning”
Your satisfaction matters to us! If you had a great experience with us, we'd love a 5-star rating and a kind review.
Worked with us? Leave a reviewService areas
We come to you anywhere in Jeddah
From Al Shiraa and Al Yaqout in the north to Al Thaghr and Al Quraiyat in the south, with our base in Al Aziziyah.
What sets this district apart
The hospital buildings on the North Corniche are modern and spacious, spread across multiple floors with diverse departments, each with different cooling demands: operating theatres need precise temperature and humidity control far more than admin areas. The coastal expansion means outdoor units face salt and sea moisture directly, requiring deeper maintenance and specialist spares. Coordination with hospital management is essential to avoid any break in critical services.
The North Corniche is a modern coastal district in north Jeddah, home to advanced hospitals and clinics with tall commercial buildings.
Most hospital cooling systems here are central multi-zone with separate controls per room, and the outdoor units run long copper and power lines across the roof or outer walls.
The AC setup in North Corniche
- 1
Multi-zone central system
Most North Corniche hospitals use a unified central cooling plant with separate ductwork and independent controls for each critical department or room.
- 2
Outdoor units on roofs and exterior walls
Large outdoor units sit on hospital roofs or coastal-facing walls, with copper runs and power lines that may exceed fifty metres.
- 3
Separate temperature and humidity sensors
Operating theatres and intensive care have precision sensors and standalone thermostats to maintain the required medical environment.
Before the visit
Before our visit in North Corniche
- 1
Coordinate the project with hospital management before start
Notify hospital management well in advance of design and maintenance dates, and clarify which departments need temporary standdown and which can operate during service.
- 2
Confirm location of outdoor units and ductwork
Confirm safe access to the roofs and exterior walls where units are mounted, and map the copper and power line routes.
- 3
Gather current sensor readings and performance data
Collect recent temperature and humidity readings from theatres and intensive care, and central system logs to assess performance before the visit.
More districts for Hospital HVAC
Other services in North Corniche
FAQ
Questions about Hospital HVAC
How do ventilation needs differ across hospital departments?
Ventilation needs vary from one department to the next based on the activity in each area and the requirements set by the facility's designer and the site survey. Operating theatres need highly filtered, directionally controlled air, while patient rooms, corridors and administrative areas each carry different requirements. We build the duct network and select units from the facility's drawings and its specific requirements, not from general assumptions.
Can systems be maintained without stopping sensitive departments?
Yes, but it requires careful planning before the maintenance date. We agree with facility management on a schedule that names the section and the right time window, then isolate the target section using dampers and blanking plates without affecting adjacent departments. Corrective tasks such as replacing a capacitor or repairing a flare joint are carried out within the agreed time window.
What governs duct network design in a medical building?
Design is governed by the approved facility drawings and each department's requirements as defined by the site survey and the specialist designer. We fabricate ducts in our own workshop from G90 galvanised sheet to project dimensions, and use Kimmco and Armaflex insulation with Foster sealants to control leakage. Distribution and pressure in each section follow the specifications drawn for that department individually.
What governs duct network design in a medical building?
Design is governed by the approved facility drawings and each department's requirements as defined by the site survey and the specialist designer. We fabricate ducts in our own workshop from G90 galvanised sheet to project dimensions, and use Kimmco and Armaflex insulation with Foster sealants to control leakage. Distribution and pressure in each section follow the specifications drawn for that department individually.
Do you work with small clinics or only hospitals?
We work with medical facilities of all sizes, from a clinic in a residential district to a multi-storey medical complex. The size of the facility does not change the principle: the site survey is the starting point, and from it we determine unit types, duct dimensions and fresh-air requirements for each zone. Preventive and corrective maintenance contracts are available for clinics and hospitals alike.
Can you service the cooling system without shutting down hospital departments?
Yes, we coordinate with hospital management to schedule maintenance during quieter periods, and work through the system in stages to keep each department in a controlled environment.
Sea salt and coastal humidity affect our outdoor units; how do you handle that?
Sea salt and coastal moisture speed up corrosion of pipes and aluminium, so we clean outdoor units regularly and replace worn parts before performance suffers.
Operating theatres need very precise temperature and humidity; how do you ensure this?
We install separate monitoring and control equipment in theatres and intensive care, and run periodic checks to keep readings within medical specifications.
Can the central system be expanded if the hospital adds new departments?
Yes, we survey the hospital first and design the system with spare capacity for future expansion, and can add new control units within the existing network.
