Charged right, not just topped up
Split AC refrigerant charging in Al Rabiyah
In Al Rabiyah, south Jeddah, split AC refrigerant charging starts with finding the leak before adding gas. A unit cooling weakly or blowing lukewarm air needs careful inspection of the copper and connections, because a small leak comes back fast if left unfixed.
- Leak found first
- Vacuum and test
- Correct charge
Clients We're Proud to Serve
Organisations and companies that trusted Alrabih with their projects.
When your split needs a refrigerant charge
- 1
Weak cooling with a clean filter
If the filter is clean and the compressor is running but the air from the indoor unit is barely cool, the cause is usually low refrigerant from a leak at the flare joints or the outdoor service valves.
- 2
Frost on the pipes or unusual water drips
Frost on the large pipe at the indoor unit, or water dripping from the unit in an unusual way, means refrigerant pressure has dropped below the range set by the manufacturer. The inspection finds the leak before any charging begins.
- 3
A split that was moved and refitted
When a split is removed for painting, renovation or a room move, the flare joints are disconnected and remade. These joints are the most likely source of a leak after refitting, and the system needs a careful check, a vacuum and a fresh charge.
Who it's for
Your bedroom split cools only at night
We find and fix the leak at the flare joints, then vacuum and charge to the nameplate refrigerant type.
Ask on WhatsAppYour split was removed for renovation and refitted
We inspect every remade flare joint, vacuum the full line, then charge and confirm cooling has returned.
Ask on WhatsApp
What the job covers
- Check flare joints and valves
- Repair or remake flare
- Vacuum line and pressure test
- Charge to nameplate refrigerant type
- Run unit confirm cooling
How we work
How we work
- 1
Describe the fault
Tell us on WhatsApp what is happening and send a photo of the outdoor unit nameplate so we know the refrigerant type before we arrive.
- 2
Inspect and find the leak
The technician checks the flare joints at the indoor unit and the service valves at the outdoor unit and locates the leak before taking any further step.
- 3
Repair and vacuum
We tighten or remake the flare joint as its condition requires, then vacuum the line and watch the pressure hold to confirm the line is tight.
- 4
Charge and run
We charge with the nameplate type at the amount the inspection determines, then run the unit and confirm that cooling has returned to the normal level.
Fix the leak first or just top it up?
| Alrabih | The usual way | |
|---|---|---|
| The leak | Found and fixed first | Ignored, charged over it |
| Flare joint | Checked, remade if needed | Not checked |
| Vacuum | Before every charge | Often skipped |
| Refrigerant type | Nameplate only | Whatever is available |
| Line moisture | Removed by vacuum | Left inside the line |
Everything your AC needs, from one team
From system design and duct fabrication to installation, commissioning and maintenance.
Split AC installation
Request this serviceDuct installation
Request this serviceCentral AC installation
Request this serviceDuct fabrication
Request this serviceCold room installation
Request this serviceElectro-mechanical works
Request this serviceChiller & AHU installation
Request this serviceHVAC design
Request this serviceAC repair & faults
Request this serviceAC cleaning
Request this serviceRefrigerant charging
Request this serviceCentral AC maintenance
Request this serviceChiller maintenance
Request this serviceAC removal & refitting
Request this serviceDuct cleaning & sanitising
Request this serviceAC servicing by brand
Request this serviceOperation & maintenance contracts
Request this serviceAHU maintenance
Request this serviceFridge & freezer service
Request this serviceCold rooms
Request this serviceDisplay fridges & chillers
Request this serviceFactory HVAC
Request this serviceWarehouse HVAC
Request this serviceVilla & home HVAC
Request this serviceHotel HVAC
Request this serviceSchool HVAC
Request this serviceHospital HVAC
Request this serviceMosque HVAC
Request this serviceMall & retail HVAC
Request this serviceRestaurant & cafe HVAC
Request this service
Some of our work
Ductwork, rooftop units and diffusers, from work we've completed in Jeddah.
Customer reviews
What our customers say
- Muhammadramzan 2641
“MashaaAllah. Services are so good. Behaviour and kindness 100/100. Prices are less then Market. Fully recommended”
- shahzeb armani
“Wow. Prices are so comfortable. Outstanding services. People are so talented and nice”
- Tawfik AlyawerLocal Guide
“U can find all u need for air conditioning”
Your satisfaction matters to us! If you had a great experience with us, we'd love a 5-star rating and a kind review.
Worked with us? Leave a reviewService areas
We come to you anywhere in Jeddah
From Al Shiraa and Al Yaqout in the north to Al Thaghr and Al Quraiyat in the south, with our base in Al Aziziyah.
What sets this district apart
Al Rabiyah is a moderate-density residential district with villas and flats of varied ages, some new and some older. The properties have reasonable spacing between them, easing access to external units. But the mix of building ages means mixed refrigerant types (R22 in older units, R410A in newer), so identifying the correct type is essential before charging. Small leaks are common in older units due to joint corrosion over time and humidity exposure.
Al Rabiyah lies in south Jeddah, a balanced residential district with villas and flats of mixed ages and reasonable spacing.
Units in Al Rabiyah are mixed: older ones use R22, newer ones use R410A, and small leaks are common, especially in older copper joints.
The AC setup in Al Rabiyah
- 1
Single R22 split in older villas
Villas built before 2010 typically have a single R22 split needing precise charging and regular leak checks.
- 2
Single R410A split in newer villas
Villas built after 2010 typically have newer R410A splits needing modern nameplate charging.
- 3
External units with reasonable spacing between properties
Al Rabiyah's property spacing is reasonable, easing access to external units and copper joint work.
Before the visit
Before our visit in Al Rabiyah
- 1
Confirm the villa's building year
Building year determines the refrigerant type (R22 pre-2010, R410A after), so tell us or show us the nameplate on the external unit.
- 2
Prepare safe access to the external unit
Units are usually on the external wall or roof, so clear any obstacles and agree on the easiest access route.
- 3
Have the electrical circuit ready
We may need to cut power during detection and charging, so confirm the circuit breaker is safely accessible.
More districts for Split AC refrigerant charging
Other services in Al Rabiyah
FAQ
Questions about Split AC refrigerant charging
Does the split have to come off the wall to be recharged?
Usually not. Charging is done at the service valve on the outdoor unit, and if the leak is at the flare joints behind the indoor unit we reach them by lifting the lower cover or tilting the unit on its bracket. It only comes down when the joint is inside the wall.
Where do leaks usually occur in a wall split?
The most common points in a wall split are the flare joints at the indoor unit, which loosen over time from vibration, and the service valves at the outdoor unit. In Jeddah's humid and salty air, oxidation at copper connections can develop faster, which raises the chance of a leak.
Does the charging process differ when a split has been moved?
When a split is moved, the flare joints are disconnected and remade, and this is when air and moisture enter the line. A full vacuum before charging becomes especially important, and the technician checks every remade flare joint before the line is closed.
Why does my split cool only at night?
This is a common sign of low refrigerant. At night, lower outdoor air temperature lets the compressor partly compensate for the shortage. During Jeddah's daytime heat, the reduced charge is not enough and cooling weakens or stops. The inspection confirms whether this is the cause or whether another factor such as the compressor or capacitor is involved.
Does the length of the copper pipe run affect how much refrigerant is needed?
Yes, a longer copper pipe run between the two units requires more refrigerant. The site inspection measures the actual run length, and the technician sets the charge amount based on the nameplate figure and the installed pipe length.
How do I tell if an older villa's split needs refrigerant or a repair?
An older unit cooling weakly usually has a leaky joint, not just a gas shortfall. We find the leak using tracer gas and fix it before charging, so it does not reoccur quickly.
Do older and newer villas in Al Rabiyah need different refrigerant types?
Yes, villas built before 2010 typically use R22, while those after 2010 use R410A. Always check the nameplate on the external unit to confirm the right type.
Does Al Rabiyah's humidity speed up leaks in copper joints?
Coastal humidity speeds up corrosion of copper joints over time, especially in older units. Routine checks and maintenance reduce leak risk.
Can a small leak in an older unit be fixed, or must the whole unit be replaced?
A small joint leak can be safely soldered without replacing the unit. But if the leak is in the indoor coil or compressor itself, replacement may be more economical.
