Central AC for apartments
Apartment central AC in Al Tilal
In Al Tilal, east Jeddah, fitting central AC in residential flats demands careful understanding of interior spacing and ceiling design. Alrabih's team studies the flat's internal layout closely, selects the optimal indoor unit location, and routes ducts intelligently to avoid conflicts with other building systems.
- Tight ceiling
- Sealed drain
- Quiet running
Clients We're Proud to Serve
Organisations and companies that trusted Alrabih with their projects.
When central AC makes sense in your flat
- 1
New flat before finishing
The finishing stage is the right time to install central AC. The ceiling is open and walls are ready for copper and drain routes, so there is no need later to cut plaster or damage finished surfaces.
- 2
Occupied flat where splits fall short
If splits leave hot and cold patches, or the noise bothers you at night, central AC distributes air evenly and hides the unit away from the room. A site survey decides whether your ceiling height allows it.
- 3
Your unit disturbs the neighbours
In apartments, neighbours hear unit vibration through shared ceilings and walls. We choose the indoor unit suspension point carefully and use flexible collars on the air outlets to absorb vibration before it reaches the building structure.
Who it's for
Living in a furnished flat and want to replace splits
We survey your ceiling void to see whether a concealed unit fits, then run copper and drain without disturbing the existing décor.
Ask on WhatsAppBuying a flat in a building under construction
We coordinate with the finishing stage to run copper, drain and ducts before ceilings and walls are closed, so every route stays fully concealed.
Ask on WhatsApp
What the installation covers
- Ceiling survey and unit position
- Mueller copper fully insulated
- Condensate drain with correct fall
- Air ducts and distributed outlets
- Line vacuum and start-up test
How we work
How we work
- 1
Ceiling and route survey
We measure the available ceiling void, decide where the indoor unit hangs, map the copper route and find where condensate drains without causing damp. The survey decides whether one zone or more suits the flat.
- 2
Run copper and drain
We run insulated Mueller copper in the void above the suspended ceiling and slope the condensate line towards the building drain or an external outlet, so no standing water causes odour or damp.
- 3
Fit ducts and outlets
We mount the indoor unit on vibration-absorbing hangers, route ducts to each room and place every outlet so air spreads evenly without blowing cold air directly onto anyone.
- 4
Vacuum, test and hand over
We vacuum the copper line to remove air and moisture, check all joints, then run the unit and confirm cooling in every room before we hand over.
A considered install or a hasty one?
| Alrabih | The usual way | |
|---|---|---|
| Indoor unit position | Set after measuring the void | Wherever it fits |
| Condensate drain | Calculated fall to building drain | May pool and cause damp |
| Vibration | Absorbing hangers, flexible collars | Reaches the neighbours |
| Air distribution | Outlets placed for even spread | Cold rooms and warm rooms |
| Salty sea air | Mueller copper, tight flared joints | Early joint corrosion |
Everything your AC needs, from one team
From system design and duct fabrication to installation, commissioning and maintenance.
Split AC installation
Request this serviceDuct installation
Request this serviceCentral AC installation
Request this serviceDuct fabrication
Request this serviceCold room installation
Request this serviceElectro-mechanical works
Request this serviceChiller & AHU installation
Request this serviceHVAC design
Request this serviceAC repair & faults
Request this serviceAC cleaning
Request this serviceRefrigerant charging
Request this serviceCentral AC maintenance
Request this serviceChiller maintenance
Request this serviceAC removal & refitting
Request this serviceDuct cleaning & sanitising
Request this serviceAC servicing by brand
Request this serviceOperation & maintenance contracts
Request this serviceAHU maintenance
Request this serviceFridge & freezer service
Request this serviceCold rooms
Request this serviceDisplay fridges & chillers
Request this serviceFactory HVAC
Request this serviceWarehouse HVAC
Request this serviceVilla & home HVAC
Request this serviceHotel HVAC
Request this serviceSchool HVAC
Request this serviceHospital HVAC
Request this serviceMosque HVAC
Request this serviceMall & retail HVAC
Request this serviceRestaurant & cafe HVAC
Request this service
Some of our work
Ductwork, rooftop units and diffusers, from work we've completed in Jeddah.
Customer reviews
What our customers say
- Muhammadramzan 2641
“MashaaAllah. Services are so good. Behaviour and kindness 100/100. Prices are less then Market. Fully recommended”
- shahzeb armani
“Wow. Prices are so comfortable. Outstanding services. People are so talented and nice”
- Tawfik AlyawerLocal Guide
“U can find all u need for air conditioning”
Your satisfaction matters to us! If you had a great experience with us, we'd love a 5-star rating and a kind review.
Worked with us? Leave a reviewService areas
We come to you anywhere in Jeddah
From Al Shiraa and Al Yaqout in the north to Al Thaghr and Al Quraiyat in the south, with our base in Al Aziziyah.
What sets this district apart
Al Tilal is a relatively modern residential district mixing flats of varied sizes with different architectural designs and ceiling styles, ranging from standard plasterboard to prefab ceilings to ornate decoration. This variety means each flat may need a bespoke central AC solution, especially if it has high ceilings in one area and low ceilings in another. Ductwork must respect other systems such as electrical circuits, plumbing and existing AC, and drainage requires careful study to prevent damp in shared walls.
Al Tilal sits in east Jeddah, a modern residential zone with varied building architecture and interior designs.
Al Tilal flats range from 100 to 250 square metres and feature diverse interior designs that each require individual study before central AC installation.
The AC setup in Al Tilal
- 1
Flexible indoor unit design by space type
Al Tilal's varied flats may need different indoor unit styles, such as horizontal units for high ceilings or compact vertical units for tight hallways.
- 2
Flexible ducts with zone-separated joints
We use flexible ducts and separate sections per area, allowing later adjustment and avoiding conflicts with other systems.
- 3
Multiple drainage points as needed
Instead of a single drain point, we may use multiple smaller drainage locations across the flat to reduce the risk of damp on shared walls.
Before the visit
Before our visit in Al Tilal
- 1
Provide the flat's architectural plan if available
If you have the original flat plan, send it so we can pre-plot duct routes and unit placement before the visit.
- 2
Mark existing electrical and plumbing locations
Before the visit, tell us where the main electrical circuits and plumbing pipes are, both visible and hidden, especially in ceilings and hallways.
- 3
Ensure ceiling and void access is clear
Check that the ceiling void is accessible through existing hatch points or whether new access points will be needed.
More districts for Apartment central AC
Other services in Al Tilal
FAQ
Questions about Apartment central AC
Is there enough ceiling space in a flat for a central unit?
It varies between flats. Slim ceiling cassettes need less void depth than full ducted units. A site survey measures what is available and decides the right type; if the corridor ceiling is too shallow we look at a storage room or bathroom ceiling instead.
Is one unit enough for the whole flat or do I need more?
It depends on the flat's area, room layout and how much sun each side receives. Two- and three-bedroom flats can sometimes work with one unit and well-planned ducts; larger flats or those with separate zones may need two. The survey decides.
Where does the outdoor unit go when the flat has no large balcony?
Options include the shared roof if the building rules allow it, a facade bracket away from neighbours' windows, or the balcony if it can take the load. We review the building's rules before recommending any position.
Jeddah's air is very humid; does that affect the condensate drain?
Yes. In Jeddah the indoor unit produces more condensate because of the high humidity. We make sure the drain line has enough fall, that the horizontal run before it drops is not too long, and that the outlet does not conflict with other flats' drainage in the building.
Can the flat be split into two zones with different temperatures?
It is possible using two separate indoor units or by adding variable-flow dampers on the duct runs. The right choice depends on the flat's layout and the ceiling void available in each zone. A site survey decides which approach suits your room arrangement.
My flat has high ceilings in some rooms and low in others, can the AC reach all rooms?
Yes, we study the flat layout first and choose duct routes to work with varied ceiling heights. We may use flexible sections or separate zones per area to ensure even air distribution.
The flat has many electrical wires and plumbing pipes, how do you route the ducts?
We map all existing electrical and plumbing routes before starting, plot duct paths to avoid any crossing or conflict, and coordinate with electricians or plumbers if needed.
The prefab ceiling might be damaged by ductwork, how do you preserve it?
We assess the prefab ceiling type first and avoid breaching weight-bearing structures. If needed, we use brackets and clips approved for that specific ceiling type.
The flat has an old window unit, must it be removed before fitting central AC?
Not necessarily. If the window unit doesn't block ductwork or drainage, it can stay. But if it's an obstruction, we recommend removing it and resealing the window after installation.
